Interior with warm timber wall panelling and a wooden reception counter
Carved solid wood double entrance door set in a stone frame
Kitchen with a walnut-finished island, timber stools and soft pendant light
Polished wooden boardroom table reflecting the room lighting

Professional wood finishing services

Where natural wood meets timeless craftsmanship.

Plate 01 — Panelled interiors

Bring out the depth, figure and warmth of real wood with finishes chosen for the surface, applied with patience and inspected in good light.

01 / 04
Living room with timber-panelled walls, a timber window frame and warm natural light
Close-up of natural wood grain

01 — The craft

The art of a beautiful wood finish.

A good finish does two jobs at once. It makes the wood look its best, and it protects the surface in the way that suits how you use it.

The right coating can deepen the colour of walnut, keep pale oak looking pale, and make the grain on a veneered wardrobe stand out instead of sitting flat under a cloudy film. It also gives the surface a barrier against everyday handling, spills and dust. How strong that barrier is depends on the system chosen.

That is why we start with the wood, not the product. We look at the surface, what is on it now, where it is and how it is used before we recommend a finish.

  • i.
    Clarity of grainClear and natural-look systems that let figure, pores and colour come through.
  • ii.
    The sheen you chooseFrom near-raw matte to deep, reflective gloss, depending on the coating system.
  • iii.
    Protection matched to useA dining table, a wardrobe and a main door have different needs. The finish should reflect that.
A finish should never hide the wood. It should help you see it.

02 — Our wood finish services

Four coating systems. Four different characters.

No single coating is right for every surface. Natural, melamine, PU and polyester finishes each look different, behave differently and suit different places in a home or office. Here is how they compare.

Natural wood sideboard with a soft low-sheen finish
MatteSatinGloss

Natural Wood Coating

Clear and natural-look coatings, such as penetrating oils, sealers and clear matte or satin topcoats, keep wood looking like wood. Grain and pores stay visible. Colour can stay close to the timber's own tone or be adjusted with a stain first.

  • Grain, pores and figure remain the hero
  • Low-sheen looks, matte through satin
  • Warm, tactile surface with a soft feel
  • Many systems can be refreshed with a maintenance coat
Well suited to
  • Solid wood furniture
  • Veneer panelling
  • Wall cladding
  • Ceilings & beams
  • Light oak & walnut

Good to know: natural-look finishes usually give a thinner film than PU or polyester. For tabletops and high-touch areas we discuss a harder-wearing clear topcoat, and we tell you plainly how often a refresh may be needed.

At a glance

General characteristics. The exact result depends on the product system, the substrate and the application.

Attribute Natural Melamine PU Polyester
Look Close to raw wood, soft and open Smooth, clear and even Refined film, clear or coloured Deep, glass-like, reflective
Grain Most visible, can be felt Visible under a smooth film Visible (clear) or hidden (opaque) Visible beneath a thick, filled film
Sheens Matte to satin Matte, satin, gloss Matte, satin, gloss High gloss
Typical use Furniture, panelling, ceilings Wardrobes, internal doors, bedroom furniture Kitchens, tops, doors, modern cabinetry Statement pieces, decorative panels
Think twice if… You want a uniform, wipe-clean film The surface is outdoors or often wet Exposure needs an exterior-grade product The surface takes knocks and scratches daily

03 — Inspiration library

Find the finish that feels like yours.

Tones, sheens and surfaces side by side. Open any plate for a closer look, and tell us which ones you like. It is the quickest way to start a conversation about your project.

Natural Grain FinishSheen
Golden Teak TonesWood tone
Smoked Wood TonesWood tone
Contemporary Wood PanelsSurface
Satin Dining TableSheen
High-Gloss Boardroom TableSheen
Wooden Ceiling BeamsSurface
Classic Kitchen CabinetrySurface
Rustic Sliding DoorWood tone
Carved Entrance DoorSurface
Light Oak Bed FrameWood tone
Walnut Bedside CabinetWood tone
Slatted Wood InteriorSurface
Light Oak Dining NookWood tone
Matte Wood StudySheen
Warm Wood Living RoomWood tone

Representative inspiration images. Real finishes vary with species, veneer, stain and coating system, so ask to see physical samples before you decide.

Book a Consultation
1 / 16

04 — Applications

Where can wood finishing be applied?

Almost anywhere there is real wood or veneer, from the main door to the ceiling above the dining table.

The right coating depends on the surface. The substrate (solid wood, veneer, plywood or MDF), its current condition, its location and its exposure to sun, water and handling all decide which system makes sense. For exterior or sun-exposed woodwork we recommend only compatible exterior-grade systems.
  1. Main entrance doors

    Exterior-exposed

    The most handled and most exposed woodwork in a home. Doors facing sun or rain need an exterior-grade, UV-resistant system.

    Often considered: Exterior-grade PU or natural exterior systems
  2. Internal wooden doors

    Interior

    Doors, frames and architraves finished to match the room, from quiet matte to refined satin.

    Often considered: Melamine, PU
  3. Wooden window frames

    Exterior-exposed

    Frames that face weather on one side and your interior on the other, so both faces are considered.

    Often considered: Exterior-grade systems on exposed faces
  4. Wardrobes & storage units

    Interior

    Large veneered surfaces where an even, consistent sheen makes the room feel calm.

    Often considered: Melamine, PU, natural
  5. Kitchen cabinets

    Interior

    Shutters that meet heat, steam and frequent cleaning, where the coating choice matters most.

    Often considered: PU
  6. Dining tables

    Interior

    Tabletops face spills, hot dishes and daily wiping, so we discuss clear, harder-wearing topcoats.

    Often considered: PU, polyester
  7. Beds & bedroom furniture

    Interior

    Headboards, side tables and dressers finished to sit comfortably together.

    Often considered: Melamine, natural, PU
  8. Wooden wall panels

    Interior

    Fluted, slatted or flat panelling where the finish controls how light falls across the wall.

    Often considered: Natural, melamine, PU
  9. Decorative partitions

    Interior

    Screens and jaalis with many edges and recesses that need patient, even coverage.

    Often considered: Natural, PU
  10. Wooden ceilings & beams

    Interior

    Overhead timber where a low-sheen finish avoids glare and keeps the wood warm.

    Often considered: Natural, melamine
  11. Office furniture

    Interior

    Desks, storage and boardroom tables that need to look sharp under daily use.

    Often considered: PU, melamine
  12. Reception desks & commercial furniture

    Interior

    Statement pieces that set the tone of a space, sometimes in high gloss.

    Often considered: PU, polyester

05 — Natural wood & veneer

Know what you are finishing.

Solid wood and veneer can look very similar once they are finished, but they are not the same material. They need different handling. Understanding the difference is the first step to a finish that lasts and looks right.

The material

Solid wood

Timber that is wood all the way through. It can usually be sanded back and refinished more than once over its life. Like all wood, it still moves with humidity, so preparation and sealing on every face matter.

The material

Veneer

A thin slice of real wood bonded to a core such as plywood or MDF. It shows genuine grain and allows matched patterns that solid boards can't. Because the wood layer is thin, it is sanded with care. Aggressive sanding can cut through to the core.

The surface

Finished wood

Either material once it is sealed and coated. The coating system decides the sheen, how much the grain shows, and how the surface handles everyday use. The material underneath decides how much preparation and refinishing it can take.

Figured wood grain with flowing, arched patterns
Figured grainArched, flowing figure, typical of crown-cut veneer and plain-sawn boards. Expressive and warm.
Dark timber boards with straight, linear grain
Straight grainCalm, linear lines, typical of quarter-cut veneer.
Golden timber boards with knots and natural colour variation
Character grainKnots and colour variation for a rustic look.
  • Why preparation mattersDust, old polish, wax and hand oils stop a new coat from bonding. The surface is cleaned and de-greased, gaps and grain are filled where the system needs it, and only then sealed.
  • Why the coating choice mattersA clear matte coat on crown-cut walnut and a high-gloss coat on the same veneer give two very different rooms. We'll show samples before you commit.
  • Why we check before sandingOn older veneered furniture we check the thickness and condition of the face first. Some pieces call for a light scuff and recoat rather than a full strip.
Interior with vertical timber slats and warm wood surfaces
Good finishing is something you notice only in the wood itself.

06 — Why finish professionally

What a professional finish gives you.

Well-chosen and well-applied coatings change how wood looks, how it feels and how it copes with daily life.

  • Enhanced natural appearance

    Colour deepens, figure becomes clearer and the wood reads as richer and more alive.

  • Refined surface aesthetics

    Proper sealing and sanding between coats gives a smooth, even surface to the touch.

  • Protection suited to the coating

    A barrier against everyday handling, dust and spills, at the level the chosen system provides.

  • Better resistance to daily wear

    Many systems help surfaces cope better with routine use and cleaning, depending on the coating.

  • Easier routine maintenance

    A sealed surface is easier to wipe clean than bare or worn wood.

  • Multiple sheen possibilities

    Matte, satin or gloss, chosen to suit the light in the room and the mood you want.

  • Improved visual consistency

    Mismatched pieces and patchy old finishes brought to one considered look.

  • Greater design flexibility

    Stains, clear coats and opaque colours open up more ways to use wood in a design.

What a coating can do depends on the system, the substrate and how the surface is used. We'll tell you what a finish can and cannot do before you choose. We do not promise scratch-proof, waterproof or termite-proof surfaces.

07 — Refinishing

From tired to refined.

Faded doors, dull tabletops and patchy cabinets can often be refinished rather than replaced. Drag the handle to see what a careful strip, prep and recoat can change.

Carved wooden door shown with a rich, even finish (illustration) The same door digitally dulled to suggest a worn finish (illustration) BeforeAfter

Illustrative visualisation. The "before" side is the same stock photograph, digitally dulled to suggest a worn finish. These are not photographs of a Khandani Painters project. Genuine before-and-after project photographs will replace them.

Dull door to refined satin

Sun and handling leave doors faded and uneven. The old coating is removed or keyed, colour is evened out, and a fresh system goes on to the sheen you choose.

  1. 01Assess the existing coating and the wood beneath
  2. 02Strip or sand back, as the surface allows
  3. 03Repair, fill and, if needed, re-stain
  4. 04Seal, coat and finish to the agreed sheen
Ask about refinishing

08 — Our wood finishing process

Six steps, no shortcuts.

Most of what makes a finish beautiful happens before the last coat goes on. This is how we approach a wood finishing project.

Orbital sander smoothing a timber surface during preparation
  1. Consultation & surface assessment

    We look at the wood, what is on it now, its condition, where it sits and the look you want.

  2. Finish selection

    We recommend a coating system based on the substrate, the use and the appearance you're after, with samples where possible.

  3. Surface preparation

    Surrounding areas are protected. Surfaces are cleaned, sanded, filled and prepared as the system requires.

  4. Application

    The selected system goes on coat by coat, following its application, sanding and curing requirements.

  5. Final inspection

    We check the finish in good light for consistency, sheen, edges and workmanship, and fix what needs fixing.

  6. Project handover

    We walk you through the finished surfaces and give you care guidance for the system used.

It starts with a conversation about your surfaces and the look you have in mind.

Book a Consultation

09 — Why Khandani Painters

Why choose Khandani Painters for wood finishing

The last coat is what you see. It is everything before it that makes it last.

We treat wood finishing as a craft of preparation, judgement and patience. That means recommending the right system for each surface, not the same one for every job.

Get an Estimate
Room with a round wooden table, timber shelving and natural light
  • 01

    Proper surface preparation

    Cleaning, sanding and filling done to suit the system, because a coating is only as good as what's under it.

  • 02

    Suitable coating recommendations

    We match the system to the substrate, location and use, and tell you when a finish isn't right.

  • 03

    Attention to detail

    Edges, corners, end grain and hardware recesses get the same care as the visible faces.

  • 04

    Quality-conscious work

    Coats are applied and cured to the system's requirements, not rushed to save a day.

  • 05

    Finish customisation

    Tone, stain and sheen tuned to your interiors, with samples to approve.

  • 06

    Project-specific consultation

    Every quotation is based on your actual surfaces, condition and scope.

  • 07

    Careful execution

    Floors, fittings and nearby surfaces are protected, and the site is left tidy.

  • 08

    Customer-focused service

    Clear communication about scope, schedule and care from enquiry to handover.

10 — Estimate

Wood finish cost estimator.

Wood finish costs typically start between ₹120 and ₹400 per sq. ft. Choose your surface and finish, enter an approximate area, and see an indicative range instantly.

01Surface type
02Wood finish type
03Approximate area sq. ft.
sq. ft.

Measure each face you want finished. For example, a 7 × 3 ft door is 21 sq. ft. per side. Not sure? Enter your best guess and we'll measure on site.

04Project details optional

11 — Questions

Wood finishing, answered.

Straight answers to the questions we're asked most. Can't find yours?

Ask us directly

What is wood finish painting?

Wood finish painting is the process of preparing a wooden surface and applying a coating system that improves how it looks and helps protect it. Depending on the result you want, that might be a clear finish that shows the grain, a stained finish that changes the tone, or an opaque finish in a solid colour.

A proper job is mostly preparation: cleaning, sanding, filling and sealing. Then the coats are applied, each one given the drying and sanding it needs.

What are the different types of wood coatings?

The four systems we work with most often are:

  • Natural coatings: oils, sealers and clear matte or satin coats that keep a near-raw look.
  • Melamine coating: a clear lacquer widely used on interior furniture and veneer.
  • PU (polyurethane) coating: a tough, refined film in clear or pigmented versions, matte to gloss.
  • Polyester coating: a high-build system polished to a mirror-like, high-gloss finish.

Each has its place. The right one depends on the wood, its location and how it will be used.

What is the difference between melamine and PU coating?

Both give a smooth, clear film and come in matte, satin or gloss. Melamine is a widely used interior lacquer, often chosen for wardrobes, internal doors and bedroom furniture. PU is generally a two-component system that forms a tougher film. It is often chosen for surfaces that see more handling, moisture or cleaning, such as kitchen shutters and tabletops. It is also available in opaque colours.

Exact performance depends on the specific products used. We'll explain the trade-offs for your surfaces before you decide.

Which wood finish is suitable for furniture?

It depends on the piece and how it's used. Wardrobes and bedroom furniture are often finished in melamine or PU. Dining and work tops usually benefit from a harder-wearing clear topcoat such as PU. Statement pieces can suit a high-gloss polyester finish. Solid wood furniture where you want to feel the grain often suits a natural finish.

We recommend a system after seeing the wood, its current finish and where it sits in your home.

Can existing wooden furniture be refinished?

In many cases, yes. Depending on its condition, the old finish may be stripped or sanded back, or simply keyed and recoated. Repairs and re-staining can be done before the new system goes on.

Veneered furniture needs more care because the wood layer is thin, so we check its condition before deciding how far to sand. Some pieces with heavy damage, loose veneer or structural problems may need repair first.

Can wood finishes be applied to veneer surfaces?

Yes. Veneer is real wood, and most clear and pigmented systems can be used on it. Veneer is a thin layer bonded to a core such as plywood or MDF, so sanding is kept light and controlled. That avoids cutting through to the core. The right sealer and coating can make veneer grain look clear and rich.

What is the difference between matte, satin and gloss finishes?

Sheen describes how much light a surface reflects.

  • Matte reflects very little. It looks close to natural wood and is forgiving of small surface marks.
  • Satin has a soft, low glow. It is a popular balance between the natural look and a polished feel.
  • Gloss reflects strongly and adds depth, but it shows fingerprints, dust and fine scratches more readily.

We can prepare samples so you can see the difference on your chosen wood tone.

How long does a wood-finishing project take?

It depends on the area, the surface's condition, how much preparation is needed and the coating system. Most systems need several coats with drying, curing and sanding between them, so it isn't a one-day job for most projects.

We give you a schedule after the site assessment, once we know the scope. Allow time for the finish to cure before heavy use.

How do I maintain finished wooden surfaces?

  • Dust and wipe with a soft, slightly damp cloth, then dry.
  • Avoid harsh cleaners, solvents and abrasive pads unless the finish's guidance allows them.
  • Use coasters, mats and trivets on tabletops.
  • Wipe spills promptly, especially near sinks and on tops.
  • Limit long exposure to direct sunlight where you can.

At handover we share care guidance specific to the system used on your surfaces.

Can exterior wooden doors be coated?

Yes, but only with a system made for exterior exposure. Sun and rain break down interior finishes, so exposed doors, frames and windows need a compatible exterior-grade, UV-resistant product. They also need correct sealing of all faces and edges. Exterior finishes need periodic maintenance, and how often depends on exposure. We'll assess the door and recommend accordingly.

How much does professional wood finishing cost?

Our indicative starting range is ₹120 to ₹400 per sq. ft. Where a project falls in that range depends on the wood surface, its existing condition, how much preparation is needed, the coating system, the finish specification and the project's complexity.

Use the estimate calculator above for a quick range. A site assessment may be needed for an accurate quotation.

How can I get a quotation from Khandani Painters?

Fill in the consultation form on this page, call us on +91 88608 82122, or message us on WhatsApp. Share photos of the surfaces if you can. We'll discuss your requirements, arrange an assessment where needed, and send a written quotation with the scope and finish clearly specified.

Living room with warm wooden flooring and furniture

12 — Enquire

Let's give your wood a more refined finish.

Tell us about your wooden surfaces and the finish you have in mind. Our team will help you explore suitable coating options and project requirements.

Consultation request

Tell us about your project

Estimate attached

Thank you, we've received your enquiry.

Our team will review your details and call you to discuss your surfaces, suitable finishes and the next steps.

Continue on WhatsApp

The Wood Studio

Let's talk about your wood.

Share a few details and our wood-finishing team will call you to discuss your surfaces, suitable finishes and the next steps.

Thank you, we've received your enquiry.

Our team will review your details and call you to discuss your surfaces, suitable finishes and the next steps.

WhatsApp enquiry